BackUp and Restore Config

A. Tujuan

1. Mengetahui cara backup and restore config pada switch dan router pada packet tracer 
2. Dapat mengetahui konfigurasi dasar dan pemberian ip pada interface di switch dan router 

B. Pendahuluan

Backup dan restore sangat dibutuhkan dalam mengelola jaringan yang kita buat, ketika router atau switch terjadi kerusakan dalam hardware atau software, kita bias mengembalikan semua konfigurasi yang kita buat kedalam router atau switch yang baru kita pasang, selain itu kita bisa menggupgrade system yang terpasang didalam router atau switch, hal yang harus diperhatikan adalah seri yang terpasang didalam cisco atau switch

C. Alat dan Bahan

1. 1 Unit PC/Leptop 
2. Packet tracer 
3. Topologi cisco 

D. Langkah Kerja

1. Buat Topologi




2. Konfigurasi switch :

Switch>en

Switch#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Switch(config)#hostname aditt

aditt(config)#exit

aditt#

%SYS-5-CONFIG_I: Configured from console by console

aditt#copy running-config startup-config

Destination filename [startup-config]?

Building configuration...

[OK]

aditt#reload

Proceed with reload? [confirm]

PT3000 Boot Loader (PT3000-HBOOT-M) Version 12.1(11r)EA1, RELEASE SOFTWARE (fc1)

Compiled Mon 22-Jul-02 18:57 by miwang

Cisco WS-CSwitch-PT (RC32300) processor (revision C0) with 21039K bytes of memory.

Switch-PT starting...

3. Setting ip address pada switch :

aditt>en

aditt#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

aditt(config)#interface vlan 1

aditt(config-if)#ip address 172.16.11.14 255.255.255.0

aditt(config-if)#no shutdown

aditt(config-if)#

%LINK-5-CHANGED: Interface Vlan1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up

aditt(config-if)#end

aditt#

%SYS-5-CONFIG_I: Configured from console by console

4. Cek ip yang terdapat di interface vlan 1 :

aditt#show interface vlan 1

Vlan1 is up, line protocol is up

Hardware is CPU Interface, address is 000a.416e.a13a (bia 000a.416e.a13a)

Internet address is 172.16.11.14/24

5. Buat config di switch :

aditt#copy running-config flash:

Destination filename [running-config]? config.text

Building configuration...

[OK]

6. Konfigurasi sever




7. Tes koneksi dari switch ke server :

aditt#ping 172.16.11.18

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 172.16.11.18, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/2 ms

8. Back up config ke server :

aditt#dir flash:

Directory of flash:/

    2  -rw-         465          <no date>  config.text

    1  -rw-     3117390          <no date>  pt3000-i6q4l2-mz.121-22.EA4.bin

64016384 bytes total (60898529 bytes free)

aditt#copy running-config tftp:

Address or name of remote host []? 172.16.11.18

Destination filename [aditt-confg]? config.text

Writing running-config...!!

[OK - 465 bytes]

465 bytes copied in 0.013 secs (35000 bytes/sec)

9. Cek config di server apakah sudah ter-copy di server



10. Restore config :

aditt#delete flash:

Delete filename []?config.txt

Delete flash:/config.txt? [confirm]

aditt#dir flash:

Directory of flash:/

    1  -rw-     3117390          <no date>  pt3000-i6q4l2-mz.121-22.EA4.bin

64016384 bytes total (60898994 bytes free)

aditt#copy tftp: flash:

Address or name of remote host []? 172.16.11.18

Source filename []? config.text

Destination filename [config.text]?

Accessing tftp://172.16.11.18/config.text...

Loading config.text from 172.16.11.18: !

[OK - 465 bytes]

465 bytes copied in 0.002 secs (232500 bytes/sec) aditt#dir flash:

Directory of flash:/

    3  -rw-         465          <no date>  config.text

    1  -rw-     3117390          <no date>  pt3000-i6q4l2-mz.121-22.EA4.bin

64016384 bytes total (60898529 bytes free)

Untuk lebih jelasnya silahkan lihat video dibawah ini :